收藏本站
Issue B.2 07/08
Page 13 of 14
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com
Power input is 1 watt; however, some power is converted into light energy. Assuming this is of the order of
200mw, the adjusted value of δT is 2.29K. The calculation now assumes that all of the dissipation, 800mw of heat,
is conducted along the thermal path, thereby ignoring any conduction and subsequent
radiation that is not direction-
ally normal to the surfaces considered, ie: conduction through the encapsulant material vertically away from the
board, and conduction horizontally away from the heat source. The calculation also assumes that there is no contri-
bution to thermal resistance at the boundaries between material layers. In practice it is improbable that perfect
transfer will occur at these transition regions, even though the bonding between layers in this example are of high
quality. In general, the calculation indicates that the measurements below are of the order of magnitude that can be
expected.
The alternate matrix product range is of a much mo
re complicated thermal design, which does not lend it-
self to a simple theoretical calculation similar to that shown above. There are multiple incident heat sources, parallel
heat conduction paths, and significantly larger surface area for stray radiation, eg. Cup above has a surface area
available for stray radiation of approximately, 25mm2
per watt of input power. A 10-watt matrix product has approxi-
mately 92.5mm2
of exposed surface per input watt.
Measurements
The key to an accurate measurement of thermal resist
ance is to obtain a reliable value for the junction tem-
perature (Tj). Since the die itself is, and must be, encapsulated during testing, and the junction is contained within
the structure of the die, direct measurement of the junction temperature by normal means is not possible.
Two methods of non-contact thermography are available, both of which rely on emitted infrared detection.
Infrared imagery by calibrated radiograph is a possibi
lity; however, in the instance of a cup product only a
small value of δT is expected which makes accurate estimation of the actual temperature gradient difficult using col-
orimetry.
The alternative measurement type is digital infrared th
ermography. This means there is an inherent uncer-
tainty in the calculation algorithm, which sometimes gives results considered unacceptably inaccurate. In this in-
stance absolute accuracy is of secondary importance because the value to be determined is a temperature differ-
ence (δT) which requires only relative values – any error in a first reading will also be present in subsequent read-
ings that are about the same value. The difference between readings is accurate.
The other significant drawback to infrared thermometers is a limitation to minimizing the spot size over
which the measurement is made. This poses a difficulty for small assemblies like an LED cup, and in particular the
added complication that the calculated temperature is an average value for the area being interrogated further com-
plicates the issue. Another concern is
sometimes raised about the ability of
this type of instrument to detect a
heated surface beyond the closest transparent radiating surface. This is a significant issue for far field measure-
ments; however, it is simple to demonstrate that this does not hold true for the near field, and particularly when the
incident beam has a known focal length.
Lednium Series Optimal X
OVTL09LG3x Series
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PD008D02517S51 DISPLAY PLASMA AVIONIC RADIO
PD009D02501S51 DISPLAY PLASMA AVIONIC RADIO
PD013D02502S51 DISPLAY PLASMA AVIONIC RADIO
PD020D02505S51 DISPLAY PLASMA AVIONIC RADIO
PD020D02507S51 DISPLAY PLASMA AVIONIC RADIO
PD029D02501S51 DISPLAY PLASMA AVIONIC RADIO
PDS1040CTL-13 DIODE SCHOTTKY DL 40V 5A PWRDI5
PDS1240CTL-13 DIODE ARR SCHTKY 40V 6A POWERDI5
相关代理商/技术参数
OVTL09LG3WW 功能描述:大功率LED - 白色 Warm White 3200K 230lm 1050mA RoHS:否 制造商:Cree, Inc. 照明颜色:Cool White 颜色温度:5000 K 光通量:280 lm 显示角:125 deg 正向电流:700 mA 正向电压:2.9 V 安装风格:SMD/SMT 系列:XMLBWW 封装:Reel
OVTL09LGAA 功能描述:大功率LED - 单色 Power Array Amber 595nm RoHS:否 制造商:Cree, Inc. 照明颜色:Blue 波长:465 nm 光强度: 光通量/辐射通量:500 mW 正向电流:350 mA 正向电压:3.1 V 安装风格:SMD/SMT 功率额定值: 系列:XB-D 封装:Reel
OVTL09LGAA 制造商:TT Electronics / OPTEK Technology 功能描述:LED LAMP COLOR:AMBER
OVTL09LGAB 功能描述:大功率LED - 单色 Power Array Blue 467nm RoHS:否 制造商:Cree, Inc. 照明颜色:Blue 波长:465 nm 光强度: 光通量/辐射通量:500 mW 正向电流:350 mA 正向电压:3.1 V 安装风格:SMD/SMT 功率额定值: 系列:XB-D 封装:Reel
OVTL09LGAB 制造商:TT Electronics / OPTEK Technology 功能描述:LED LAMP COLOR:BLuE
OVTL09LGAG 功能描述:大功率LED - 单色 Power Array Green 524nm RoHS:否 制造商:Cree, Inc. 照明颜色:Blue 波长:465 nm 光强度: 光通量/辐射通量:500 mW 正向电流:350 mA 正向电压:3.1 V 安装风格:SMD/SMT 功率额定值: 系列:XB-D 封装:Reel
OVTL09LGAG 制造商:TT Electronics / OPTEK Technology 功能描述:LED LAMP COLOR:GREEN
OVTL09LGAM 功能描述:大功率LED - 多色 Power Array RGB Full Color RoHS:否 制造商:Cree, Inc. 照明颜色:RGB, Cool White 波长/色温: 光强度: 系列: 封装:Reel